FEATURES OF THE MODIFIED CONCRETE STRENGTH IN CLIMATIC CONDITIONS OF THE MIDDLE EAST COUNTRIES
Article Sidebar
Main Article Content
Abstract
Discusses the results of the study to determine the effects of climatic factors in the Middle East countries on the strength of concrete. It was found complex positive influences on strength when increased the temperatures and humidity at the stage of curing concrete, which means allowing to increase the strength of concrete. The experiments were carried out on the modified concrete by superplasticizers that based on sulfonated naphthalene formaldehyde compounds, including applied in the Middle East. Production samples of concrete, stored and tested them is in according to operating normative documents in territory of Belarus and the American standards.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
Механизм действия пластификаторов [Электронный ресурс] // Добавки, регулирующие свойства. – Новгород, 2007. – Режим доступа: http://www.baurum.ru. – Дата доступа: 01.10.2014.
Технологический регламент производства разжижителя С-3 / Новомосковский завод органического синтеза. – М., 1981. – 300 с.
Technical Data Sheet for Properties of Admixtures / SODAMCO-WEBER COMPANY, P.O. Box. 55–44. – Beirut, 2014. – 2 p.
ASTM C 494/C 494M. Standard Specification for Chemical Admixtures for Concrete, ASTM International, West Conshohocken, 1999. – 9 p.
Куприянов, Н.Н. Исследование влияние относительной влажности среды при тепловой обработке на формирование структуры и свойства бетона: автореф. дис. ... канд. техн. наук: 05.23.08 / Н.Н. Куприянов. – М., 1974. – 24 с.
Добавки для бетонов и строительных растворов. Общие технические условия: ГОСТ 24211-2003. – Взамен ГОСТ 24211-91; Введ. 01.03.2004. – М.: Межгосударств. Стандарт Рос. Федерации, 2004. – 18 с.
Whiting, D. Effects of High-Range Water Reducers on Some Properties of Fresh and Hardened concretes, Research and Development Bulletin RD061 / D. Whiting, 1979. – 15 p.
Смеси бетонные. Технические условия. Методы определения удобоукладываемости: СТБ 1035-96. – Взамен ГОСТ 10181.1-81; Введ. 01.05.2009. – Минск: Госстандарт Республики Беларусь, 2009. – 17 с.
Методы определения прочности на сжатие по контрольным образцам: ГОСТ 10180-90. Бетоны. – Взамен ГОСТ 10180-78; Введ. 01.01.91. – М.: Стройиздат, 1990. – 45 с.
Бетоны. Методы определения плотности: ГОСТ 12730.1-78. – Взамен ГОСТ 12730-67; Введ. 01.01.80. – М.: Стройиздат, 1980. – 5 с.
Most read articles by the same author(s)
- A. BAKATOVICH, THE MAIN PROPERTIES OF THERMAL INSULATION PLATES WITH THE USE OF SPHAGNUM MOSS, REEDS AND STRAW, Vestnik of Polotsk State University. Part F. Constructions. Applied Sciences: No. 8 (2018)
- A. BAKATOVICH, R. OBROMPALSKY, EVALUATION OF THE EFFECTIVENESS OF BIRCH BARK BY PHYSICAL INDICATORS AS A RAW MATERIAL SOURCE FOR THE PRODUCTION OF THERMAL INSULATION, Vestnik of Polotsk State University. Part F. Constructions. Applied Sciences: No. 2 (2024)
- N. DAVYDENKO, A. BAKATOVICH, OPERATIONAL CHARACTERISTICS AND TECHNOLOGICAL FEATURES OF STRAW-BOON PLATES MANUFACTURING, Vestnik of Polotsk State University. Part F. Constructions. Applied Sciences: No. 16 (2015)
- N. DAVYDENKO, A. BAKATOVICH, IMPROVEMENT OF WATER-RESISTING PROPERTIES OF LIQUID GLASS APPLIED AS A BINDING AGENT FOR HEAT-INSULATING STRAW-BOOM PLATES MANUFACTURING, Vestnik of Polotsk State University. Part F. Constructions. Applied Sciences: No. 8 (2015)