INFLUENCE OF DEFORMATION ON THE MECHANICAL PROPERTIES OF TIN-PLATED TIN
Article Sidebar
Main Article Content
Abstract
Annotation. The influence of deformation on the mechanical properties of the characteristic layers of tin plate when a through hole is pierced in it is considered. Graphic dependences are obtained showing the change in the microhardness of the outer and inner layers of tinned tin along the thickness of the sheet material depending on the angle of its bending, the integrity of the outer tinned layer of tinplate in the finished product is studied. It has been established that the integrity of the coating is preserved up to the point of plastic rupture by the piercing of the press in the central part of the workpiece. An analysis of the distribution of microhardness values showed that the inner layer has higher values than the outer ones, the maximum value of the hardening degree is observed in the outer layer (+17,1%). At values of the bending angle of more than 150 degrees, the values of the degree of hardening in all layers tend to the same value (approximately 12,75%). Analysis of the graph of changes in the degree of hardening of the sheet layers along the bending line of the sample showed that the degree of hardening of the middle layer occurs with any change in the shape of the sheet material, regardless of the degree of hardening of the outer layers.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
Zinov'ev, A.V. & Trusov, V.A. (2008). Rossyyskaya metallurhyya – nastoyashchee y budushchee [Russian metallurgy – present and future]. Novi materialy i tekhnolohiyi v metalurhiyi ta mashynobuduvanni [New materials and technologies in metallurgy and mechanical engineering], (1), 151–159. (In Russ., abstr. in Engl.).
Zinovʹyeva, N.G. (2022). Chernaya metallurgiya mira i Rossii v usloviyakh pandemii [Ferrous metallurgy of the world and Russia in a pandemic]. Chernaya metallurgiya Byulletenʹ nauchno-tekhnicheskoy i ekonomicheskoy informatsii [Ferrous metallurgy. Bulletin of scientific, technical and economic information], Т. 76, (7), 657–664. (In Russ., abstr. in Engl.).
Lenard, J.G. (2014). Primer on flat rolling. Hoboken: Elsevier Science. DOI: 10.1016/C2012-0-06474-5
Samiee, P. Niari, Е. & Ghandi, Е.Е. (2021). Thermal and structural behavior of cold-formed steel frame wall under fire condition. Engineering Structures, (252), 113563. DOI: 10.1016/j.engstruct.2021.113563/
Yun, X., Meng, Х. & Gardner, L. (2022). Design of cold-formed steel SHS and RHS beam-columns considering the influence of steel grade. Thin-Walled Structures, (171), 108600. DOI: 10.1016/j.tws.2021.10860
Wang, D., Liu, H. & Liu, J. (2017). Research and Development Trend of Shape Control for Cold Rolling Strip. Chinese Journal of Mechanical Engineering, (30), 1248–1261. URL: https://cjme.springeropen.com/articles/10.1007/s10033-017-0163-8.
Most read articles by the same author(s)
- V. FRUCKI, S. PILIPENKO, ALTERNATIVE MATERIALS REPAIR ROTARY GROUP, THE PUMP-MOTORS, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2019)
- S. PILIPENKO, O. SHTEMPEL, V. FRUTSKIY, V. KOSTRITSKIY, RESTORING THE FUNCTIONALITY OF THE “NEEDLE-BODY” CONNECTION OF THE DIESEL ENGINE NOZZLE SPRAYER, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2021)
- S. PILIPENKO, V. GRIGORENKO, INCREASING THE ACCURACY OF DETERMINING THE Q-FACTOR IN CONTROL SECTIONS OF THE STAN DEFORMATION CONE COLD PILGER ROLLING PIPE, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2021)
- A. RADIONOV, N. ZAKREVSKAYA, S. PILIPENKO, O. SHTEMPEL', ANNEALING OF COLD-ROLLED STRIPS IN SHIELDING GAS ATMOSPHERE, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 2 (2023)
- S. PILIPENKO, V. TERESHCHENKO, A. DUDAN, INFLUENCE OF COLD PIPE ROLLING PARAMETERS TO CHANGE THE WALL THICKNESS ALONG THE CONF OF DEFORMATION, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2018)
- S. PILIPENKO, A. DUDAN, DEVELOPMENT OF THE METHOD OF CALCULATION OF HEAT EXCHANGES FROM PLASTIC DEFORMATION AT COLD PILGRER ROLLER PIPE, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2018)
- S. PILIPENKO, V. FRUCKI, M. KONON, THERMAL PROPERTIES OF GAS-THERMAL REPAIR COATINGS SHAFTS TO FIT BEARINGS , Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2019)
- S. PILIPENKO, METHOD FOR CALCULATION OF BROADENING DURING COLD ROLLING OF STRIPS, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 1 (2023)
- S. PILIPENKO, ANALYSIS OF THE INFLUENCE OF SEPARATE CALIBRATION PARAMETERS OF THE WORKING TOOL OF THE COLD ROLLING PIPES MILLS ON THE Q-FACTOR DISTRIBUTION ALONG THE DEFORMATION CONE, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2020)
- S. PILIPENKO, PARAMETERS OF THE DEFORMATION CONTAINMENT VOLUME AT THE BACKWARD STROKE OF COLD-DIE-PILGERING AND COLD-ROLLER-PILGERING MILLS WHEN FEEDING THE BILLET IN EITHER POSITIONS OF THE STAND, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 2 (2024)