SELECTION OF THE OPTIMAL PARAMETERS OF THE SURFACE LAYERS OF THE STRUCTURE TRIBOSYSTEMS TAKING INTO ACCOUNT THE MECHANICAL PROPERTIES OF THE GRADIENT
Article Sidebar
Main Article Content
Abstract
The practical application of methodology to predict the optimal structure of the surface layers, formed during the operations of tribological conjunction elements, is addressed. The technique is based on the determination of the mean value of surface layers micro-hardness of the material at some local area of deformed by friction contact surfaces up to 80 mkm depth. The possibility of predicting the wear of contact surfaces, under rolling with varying degrees of slipping, from the value of the effective (“Integral”) micro-hardness, taking into account the micro-hardness of the surface of the metal layers in the process of structural adaptability at friction and gradient distribution of micro-hardness depth of the deformable layer is presented. The correlation is established between the wear of tribological conjunction elements and micro-hardness values of both tribosystems surface layers and its gradient distribution and allows to develop practical recommendations for modification of technological modes of elements of friction units.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
Оптимизация технологии нанесения покрытий по критериям прочности и износостойкости / Б.А. Ляшенко [и др.] ; под ред. В.В. Харченко. – К. : Ин-т проблем прочности, 2010. – 193 с.
Ognjanovic М. Progressive Gear Teeth Wear and Failure Probability Modeling / М. Ognjanovic // Tribology in industry. – 2004. – Vol. 26, № 3&4. – P. 44–49.
Проблема оценки износа сопряжений зубчатых колес транспортных машин и энергетического оборудования / А.П. Бурдуков [и др.] // Ползуновский вестник. – 2010. – № 1. – С. 99–105.
Кинетика изнашивания контактных поверхностей при использовании добавки фуллерена С60 к моторному маслу / Н.Ф. Дмитриченко [и др.] // Трение и износ. – 2009. – Т. 30, № 6. – С. 550–555.
Surfactant effects on the residual internal stresses in hydrated mineral binders / E.D. Shchukin [et al.] // Abstracts of the 13-th International Symposium on Surfactants in Solution, Gainesville, Florida, June 11–16, 2000. – Р. 163.
Механизм формирования защитного граничного смазочного слоя / Б.И. Ковальский [и др.] // Изв. ТулГУ : Технические науки. – 2014. – Вып. 3. – С. 26–32.
Hutchings, I.M. Tribology: friction and wear of engineering materials / I.M. Hutchings ; ed. Butterworth. – Heinemann, Oxford, 1992. – P. 58–76.
Magalhães, L. Austempered ductile iron (ADI) gears : Power loss, pitting and micropitting / L. Magalhães, J. Seabra and R. Martins // Wear. – 2007. – Vol. 264. – P. 839–849.
Cheng, H.S. Elastohydrodynamic Lubrication, in Handbook of lubrication / H.S. Cheng, E.R. Booser ; Ed. CRC Pres : Boca Raton, 1983. – P. 155–160.
A fracture mechanics model for the analysis of micro-pitting in regard to lubricated rolling – sliding contact problems / B. Zafosnik [et al.] // International Journal of Fatigue. – 2007. – Vol. 29, Iss. 9–11. – P. 1950–1958.
Sadeghi, F. Subsurface Stresses in Rolling / Sliding Machine Components / F. Sadeghi, C. Ping Sui // International Compressor Engineering Conference, 1988. – P. 680.
Tobie, Т. Case Depth and Load Capacity of Case-Carburized Gears / T. Tobie, P. Oster, B. Höhn // Gear Technology. – 2002. – March/April. – P. 31–38.
Пристрій для оцінки триботехнічних характеристик трибоелементів : корисна модель UA 88748 / О.О. Мікосянчик. – Опубл. 25.03.14.
Выбор критерия при оценке параметров прочности функционально-градиентных конструкций / Н.О. Кузин [и др.] // Технологічний аудит та резерви виробництва. – 2015. – № 6/1(26). – С. 4–8.
Most read articles by the same author(s)
- A. DUBKO, N. CHVERTKO, A. LEBEDEV, A. DUDAN, HISTORICAL ASPECTS OF THE DEVELOPMENT OF ELECTROSURGERY, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2021)
- V. ZHORNIK, A. ZAPOLSKY, A. IVAKHNIK, A. DUDAN, TECHNOLOGIES AND EQUIPMENT FOR PRODUCTION BIODEGRADABLE GREASES, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2022)
- A. DUDAN, T. VIGERINA, V. KRAVCHUK, I. PILIPENOK, INCREASED WEAR RESISTANCE OF PARTS HEAVY-LOADED FRICTION ASSEMBLY OF VEHICLES, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 10 (2022)
- S. PYLYPENKO, A. DUDAN, D. RADULЕVIC, INFLUENCE OF THE BENDING RADIUS OF PIPES ON STRENGTH PARAMETERS AUTOMOBILE PIPELINES, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2019)
- A. GRIGORCHIK, E. ASTRASHAB, M. BELOTSERKOVSKIY, V. KUKAREKO, A. SOSNOVSKIY, A. DUDAN, WEAR RESISTANCE OF GAS-THERMAL COATINGS FROM COPPER-ALLOYS ON THE BASIS OF COPPER OBTAINED BY HIGH-SPEED METALLIZATION METHOD, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2019)
- М. BELOTSERKOVSKIJ, A. DUDAN, A. YALOVIK, RECONDITIONING AND TESTING OF A HYDROLIC POWER CYLIN-DER ROD, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2021)
- M. BELOTSERKOVSKY, I. TARAN, P. KOT, A. DUDAN, TECHNOLOGY FOR OBTAINING AND TRIBOTECHNICAL CHARACTERISTICS OF OXIDIZED ALUMINUM COATINGS APPLIED TO POLYMERS , Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2019)
- А. SMYRNOV, Т. SMYRNOVА, А. DREEV, A. DUDAN, OPTIMIZATION OF THE TECHNOLOGICAL PROCESS OF RESTORING AND STRENGTHENING SURFACES WITH TASKED CHARACTERISTICS AS A CLOUD SERVICE, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2020)
- S. PILIPENKO, V. TERESHCHENKO, A. DUDAN, INFLUENCE OF COLD PIPE ROLLING PARAMETERS TO CHANGE THE WALL THICKNESS ALONG THE CONF OF DEFORMATION, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2018)
- M. M., A. SOSNOVSKIY, A. GRIGORCHIK, A. ELOVIC, A. DUDAN, FEATURES OF COATINGS OF PSEUDOPLANES METHOD OF HYPERSONIC METALLIZATION, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2018)