IMPROVING THE DESIGN OF BLOCK-MODULAR FACE MILLS BASED ON THE RESEARCH OF CUTTING PROCESS CHARACTERISTICS
Article Sidebar
Main Article Content
Abstract
The problem of improving the design of block-modular face mills based on research of cutting process characteristics is investigated. The results of experimental research of temperature in the cutting zone, noise and vibrations of the technological system, roughness of the treated surface depending on the cutting conditions are presented. Based on the obtained data an experimental model (layout) of the milling cutter using modern 3D-printing technology for high-precision machining of flat surfaces was made.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
Попок, Н.Н. Анализ тенденций проектирования инструментальных систем : в 3-х ч. / Н.Н. Попок // Вестник Полоцкого государственного университета. Серия В, Промышленность. Прикладные науки. – 2012. – № 3. – Ч. 3 : Инструментальные системы для многоцелевой обработки. – С. 19–37.
Способ установки сменной режущей пластины в режущем инструменте : пат. BY 19260 / Н.Н. Попок, В.А. Терентьев, Р.С. Хмельницкий, А.В. Сидикевич, И.Я. Сопиков. – Выдано 2014.12.12.
Режущий инструмент : пат. BY 5407 / Н.Н. Попок, В.А. Терентьев, Р.С. Хмельницкий, А.В. Сидикевич, И.Я. Сопиков. – Выдано 2014.12.12.
Многолезвийный блочно-модульный режущий инструмент : пат. BY 563 / Н.Н. Попок, В.А. Терентьев. – Выдано 2002.06.30.
Попок, Н.Н. Совершенствование системы закрепления пластин режущих и блоков резцовых в блочно-модульных режущих инструментах / Н.Н. Попок, А.С. Максимчук, С.А. Портянко // Вестник Полоцкого государственного университета. Серия В, Промышленность. Прикладные науки. – 2015. – № 3. – С. 16–22.
Фрезы торцовые нерегулируемые с клиновым креплением многогранных твердосплавных пластин. Технические условия : ГОСТ 26596-91. – М. : Стандартинформ, 2010. – 6 с.
Инструмент металлорежущий. Правила приёмки : ГОСТ 23726-79. – М. : Изд-во стандартов, 1979. – 7 с.
Most read articles by the same author(s)
- N. POPOK, R. HMELNICKY, V. ANISIMOV, PROCESSING TECHNOLOGY FOR PARTIAL SPHERICAL SURFACES OF MACHINE PARTS, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2018)
- N. POPOK, R. HMELNITSKI, S. PORTYANKO, CONTROL OF HEAT AND COOLING FLOWS IN RAPID MACHINING OF INCOMPLETE SPHERICAL SURFACES OF MACHINE PARTS, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 1 (2024)
- N. POPOK, I. KUNTSEVICH, R. HMELNICKY, V. ANISIMOV, G. GVOZDZ, INFLUENCE OF TOOL CUTTING EDGE ANGLES AT ROUGHNESS OF THE PROCESSED SURFACE OF THE SPHERE , Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2018)
- N. POPOK, V. ANISIMOV, DYNAMICS OF MECHANICAL MACHINING WITH END MILLS ON CNC MACHINE, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 1 (2024)
- N. POPOK, R. HMELNICKY, V. ANISIMOV, G. GVOZDZ, V. KUKAREKO, KINEMATIC AND TECHNOLOGICAL SUPPORT FOR FORMING THE REGULAR MICRORELIEF OF SPHERICAL SURFACES OF PARTS BY COMBINED CUTTING WITH CUTTING, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2017)
- N. POPOK, A. FRIK, ANALYSIS OF THERMOCOUPLES FOR MEASURING TEMPERATURE IN RUBBER MIXERS, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 2 (2024)
- N. POPOK, M. CHERNEVICH, G. GVOZD, MODEL AND ALGORITHM FOR DESIGNING OF BLOCK-MODULAR CUTTING TOOLS, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2017)
- N. POPOK, D. LATUSHKIN, Y. MAHAKINSKY, N. PUTEEV, MODELING OF THE TECHNOLOGICAL FACTORS INFLUENCE ON THE PRECISION OF GEARS IN THE TOOTH REGRINDING, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2017)
- N. POPOK, A. BALYSH, NON-WELDED SEALED FITTINGS FOR SMALL DIAMETER PIPELINES AND TUBING, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 2 (2024)
- N. POPOK, I. KUNCEVICH, R. HMELNICKY, V. ANISIMOV, MODELLING OF INFLUENCE OF ROUGHNESS OF THE SPHERICAL SURFACE OF THE PART ON FEED SPEED SELECTION OF THE ROTATING CUTTING TOOL, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2016)