MODELING OF THE TECHNOLOGICAL FACTORS INFLUENCE ON THE PRECISION OF GEARS IN THE TOOTH REGRINDING
Article Sidebar
Main Article Content
Abstract
The influence of technological factors on the roughness of the surface of the gear wheels after grinding is investigated. The research tasks are formulated. The results of experiments are presented. The mathematical modeling of the process under study was performed. A formula for predicting changes in the roughness of gears, depending on the parameters of the grinding wheel speed, as well as the vertical and radial feed rates of the wheel is given.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
Основные нормы взаимозаменяемости. Передачи зубчатые цилиндрические. Допуски : ГОСТ 1643-81 ; Введ. 21.04.1981. – М. : Изд-во стандартов, 1981. – 42 с.
Сильвестров, Б.Н. Справочник молодого зуборезчика : учеб. пособие / Б.Н. Сильвестров. – М. : Высш. шк., 1981. – 199 с.
Основы теории проектирования технических систем : учеб. пособие для студентов вузов / Е.И. Махаринский [и др.] ; УО «ВГТУ». – Витебск : Витеб. гос. технол. ун-т, 2009. – 354 с.
Most read articles by the same author(s)
- N. POPOK, R. HMELNICKY, V. ANISIMOV, PROCESSING TECHNOLOGY FOR PARTIAL SPHERICAL SURFACES OF MACHINE PARTS, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2018)
- N. POPOK, R. HMELNITSKI, S. PORTYANKO, CONTROL OF HEAT AND COOLING FLOWS IN RAPID MACHINING OF INCOMPLETE SPHERICAL SURFACES OF MACHINE PARTS, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 1 (2024)
- N. POPOK, I. KUNTSEVICH, R. HMELNICKY, V. ANISIMOV, G. GVOZDZ, INFLUENCE OF TOOL CUTTING EDGE ANGLES AT ROUGHNESS OF THE PROCESSED SURFACE OF THE SPHERE , Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2018)
- N. POPOK, V. ANISIMOV, DYNAMICS OF MECHANICAL MACHINING WITH END MILLS ON CNC MACHINE, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 1 (2024)
- N. POPOK, R. HMELNICKY, V. ANISIMOV, G. GVOZDZ, V. KUKAREKO, KINEMATIC AND TECHNOLOGICAL SUPPORT FOR FORMING THE REGULAR MICRORELIEF OF SPHERICAL SURFACES OF PARTS BY COMBINED CUTTING WITH CUTTING, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2017)
- N. POPOK, S. PORTSIANKO, A. MAKSIMCHUK, IMPROVING THE DESIGN OF BLOCK-MODULAR FACE MILLS BASED ON THE RESEARCH OF CUTTING PROCESS CHARACTERISTICS, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2017)
- N. POPOK, A. FRIK, ANALYSIS OF THERMOCOUPLES FOR MEASURING TEMPERATURE IN RUBBER MIXERS, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 2 (2024)
- N. POPOK, M. CHERNEVICH, G. GVOZD, MODEL AND ALGORITHM FOR DESIGNING OF BLOCK-MODULAR CUTTING TOOLS, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2017)
- N. POPOK, A. BALYSH, NON-WELDED SEALED FITTINGS FOR SMALL DIAMETER PIPELINES AND TUBING, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 2 (2024)
- N. POPOK, I. KUNCEVICH, R. HMELNICKY, V. ANISIMOV, MODELLING OF INFLUENCE OF ROUGHNESS OF THE SPHERICAL SURFACE OF THE PART ON FEED SPEED SELECTION OF THE ROTATING CUTTING TOOL, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2016)