DESIGN PROCEDURE OF POWER INPUTS ON CRUSHING IN A VERTICAL ROLL MILLS
Article Sidebar
Main Article Content
Abstract
In article results theoretical and experimental researches of power of process of crushing in a vertical roll mill are resulted. The model of destruction of a material under the influence of the pressure created rotating rolls, for the first time considering as frequency rate of influence is developed at change of degree of crushing and a specific surface, and an expense of energy for not elastic deformations, work of forces of a friction and creation of new surfaces on which basis the design procedure of power inputs on process of destruction of a material is offered. Calculations of power inputs on crushing have shown good convergence not only with experimental data, but also with data on maintained abroad to vertical roll mills.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
Kotowski, C. Gleichzeitige Herstellung von Kalksteinmehl und Kornungen minns 1,2 mm mit einer MPS – Walzenschussenmuhlen / C. Kotowski, U. Schnabel, Y. Reichardt // Zement – Kalk – Gips int. – 2003. – Jhrg. 56, № 6. – S. 73 – 75.
Йоргенсен, С.В. Вертикальная мельница для помола цемента и шлака / С.В. Йоргенсен // Цемент и его применение. − 2005. − № 3. – С. 22 – 26.
Летин, Л.А. Среднеходные и тихоходные мельницы / Л.А. Летин, К.Ф. Роддатис. – М.: Энергоиздат, 1981. – 360 с.
Селективное разрушение минералов / В.И. Ревнивцев [и др.]; под ред. В.И. Ревнивцева. – М.: Недра, 1988. – 286 с.
Осокин, В.П. Молотковые мельницы / В.П. Осокин. – М.: Энергия, 1980. – 176 с.
Ходаков, Г.С. Физика измельчения / Г.С. Ходаков. – М.: Наука, 1972.
Вайтехович, П.Е. Исследование влияния работы параметров валковых мельниц на удельные энергозатраты / П.Е. Вайтехович, В.С. Францкевич // Строительная наука и техника. − 2007. − № 2. – С. 21 – 24.
Янг, О. Разработки и производственный опыт использования вертикальных валковых мельниц в цементной промышленности / О. Янг, Р. Биссо // Цемент и его применение. − 2000. − № 2. – С. 8 – 15.
Most read articles by the same author(s)
- R. LANKIN, V. FRANTSKEVICH, INFLUENCE OF GEOMETRIC PARAMETERS OF SUPPORT-DISTRIBUTION GRIDES ON HYDRODYNAMICSIN A MASS EXCHANGER WITH A MOVABLE BALL NOZZLE, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 2 (2023)
- P. VAITEKHOVICH, G. KHVES’KO, D. BOROVSKIY, DETERMINATION OF AXIAL EFFORTS IN FRICTIONAL DRIVE OF A PLANETARY MILL, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2018)
- R. LANKIN, V. FRANTSKEVICH, A. VOLK, DEVELOPMENT AND INVESTIGATION OF PACKING ELEMENTS TO ENHANCE ABSORPTION EFFICIENCY, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 1 (2025)
- V. FRANTSKEVICH, P. VAITSEHOVICH, A. DOROGOKUPETS, MODEL OF MOTION OF MATERIAL ON SEPARATION DEVICE OF MILL, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2016)
- A. DOROGOKUPETS, P. VAITSEHOVICH, V. FRANTSKEVICH, INFLUENCE OF TECHNOLOGICAL PARAMETERS OF THE DYNAMIC QUALIFIER ON AERODYNAMICS AND EFFICIENCY OF CLASSIFICATION OF THE CRUSHED PRODUCT IN THE MILL, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2013)