INCREASING THE ACCURACY OF DETERMINING THE Q-FACTOR IN CONTROL SECTIONS OF THE STAN DEFORMATION CONE COLD PILGER ROLLING PIPE

Main Article Content

S. PILIPENKO
V. GRIGORENKO

Abstract

The influence of the method for calculating the initial values of the geometric parameters of the deformation cone on the accuracy of determining the nature of the distribution of the Q-factor along the deformation cone of the cold rolling mill mill is investigated as an important factor that creates the necessary deformation conditions that ensure the formation of the required texture of pipes made of Ti-3Al-2.5V alloy. The research methods were based on the existing dependence describing the effect of true cross-section compressions along the deformation cone on the value Q-factor in this section, as well as a number of dependencies, derived by different authors to determine the initial values of the geometric parameters of an arbitrary section of the deformation cone before the double stroke of the stand of the KhPT mill. Within the framework of this, a “direct” method of determining the initial values of the geometric parameters of an arbitrary section of the deformation cone, based on the interpolation of the calibration data of the tool of the cold rolling mill, has been proposed. The algorithm of the “direct” method for calculating the initial values of the geometric parameters of the deformation cone makes it possible to more accurately determine both these values and the accuracy of the Q-factor when using other methods (according to the formulas of Ya.E. Osada, B.M. Rogov and a simplified formula for determining the amount of reduction) for determining the considered deformation parameters for calculating the value of the Q-factor.

Article Details

How to Cite
PILIPENKO, S., & GRIGORENKO, V. (2021). INCREASING THE ACCURACY OF DETERMINING THE Q-FACTOR IN CONTROL SECTIONS OF THE STAN DEFORMATION CONE COLD PILGER ROLLING PIPE. Vestnik of Polotsk State University. Part B. Industry. Applied Sciences, (11), 18-24. Retrieved from https://journals.psu.by/industry/article/view/882
Author Biographies

S. PILIPENKO, Polotsk State University

канд. техн. наук, доц.

V. GRIGORENKO, Национальный технический университет «Днепровская политехника», Днепр

д-р техн. наук, проф.

References

Pilipenko. S.V. Deformation mode in a cold rolling condition to provide the necessary texture of the Ti-3Al-2.5V alloy / S.V. Pilipenko, V.U. Grigorenko, O.O. Bohdanov // Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. – 2021. – № 1. – С. 78–83. DOI: https://doi.org/10.33271/nvngu/2021-1/078.

Пилипенко, С.В. Исследование точности определения обжатия по толщине стенки вдоль конуса деформации за двойной ход клети станов ХПТ / С.В. Пилипенко // Сталь. – 2017. – № 2. – С. 94–97.

Пилипенко, С.В. Анализ влияния технологических факторов процесса холодной прокатки труб на изменение распределения Q-фактора вдоль конуса деформации / С.В. Пилипенко // Изв. высш. учеб. заведений. Цв. металлургия. – 2019. – № 3. – С. 30–35.

Определение технологической возможности изготовления нового вида бесшовных труб TrEx из титанового сплава Ti-3Al-2.5V / Я.И. Космацкий [и др.] // Качество в обработке материалов. – 2016. – № 2 (6). – С. 15–22.

Rui, L. Quasi-Static and Dynamic Properties of Ti-3Al-2.5V Titanium Alloy Tubes. / Liu Rui, Li Yang // IOP Conference Series: Materials Science and Engineering. – 2018. – V. 381. – Р. 1–5. DOI: 10.1088/1757-899X/381/1/012167.

Texture Development of Ti-3Al-2.5V Titanium Alloy Tubes / Z. Li [et al.] // Rare Metal Materials and Engineering. – 2017. – V. 46. – Р. 233–239. DOI: 3169-3175. 10.1016/S1875-5372(18)30023-7.

Influence of texture on mechanical properties of titanium alloy tubes / V. Vakhrusheva [et al.] // Physical Metallurgy and Heat Treatment of Metals. – 2019. – V. 844. – Р. 182–187. DOI: 10.30838/J.PMHTM.2413.241219.16.596.

Texture evolution and controlling of high-strength titanium alloy tube in cold pilgering for properties tailoring / Н. Li [et al.] // Journal of Materials Processing Technology. – 2019. – V. 279. – Р. 116520. DOI: 10.1016/j.jmatprotec.2019. 116520.

Мищенко, А.В. Состояние и тенденции развития производства холоднокатаных труб из сплавов на основе титана / А.В. Мищенко // Металл и литье Украины. – 2019. – № 3-4. – С. 310–311.

Grigorenko, V.U. Variation in wall thickness of cold-rolled pipe / V.U.Grigorenko, S.V. Pilipenko // Steel in Translation. – 2008. – 38 (9). – Р. 775–776. DOI: 10.3103/S0967091208090209.

Шевакин, Ю.Ф. Калибровка и усилия при холодной прокатке труб / Ю.Ф. Шевакин. – М. : Металлургия, 1963. – 212 с.

Геометрия прокатного инструмента и алгоритмы его расчета для станов холодной прокатки труб / В.Ф. Балакин [и др.] // Совершенствование производства стали, труб и железнодорожных колес // под ред. А.Г. Величко, В.И. Большакова, В.Ф. Балакина. – Днепропетровск : Экономика, 2015. – С. 434–450.

Most read articles by the same author(s)