INFLUENCE OF SURFACE PLASTIC DEFORMATION ON GEOMETRICAL PARAMETERS WHEN RESTORING THE CRANKSHAFT BEARING JOURNALS
Article Sidebar
Main Article Content
Abstract
The article presents the influence of surface plastic deformation on the microprofile of a strengthened surface, its roughness and changes in the curve of the supporting surface. Justified coating microstructure obtained by welding low carbon alloy wire in shielding gases, which has a high tendency to strain hardening. The degree of plastic deformation and the dependence of the relative depth of the plastic deformation of the contact pressure run-in roller, thus recommend the best value roller pressing force. To harden journals of crankshafts developed special equipment, including two break-in. Their use allows to receive a demanded contact pressure at smaller efforts of pressing of the tool and to carry out processing in the conditions of limited axial movement and fatigue limit of shafts.
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
Молодык, Н.В. Восстановление деталей машин: справочник / Н.В. Молодык, А.С. Зенкин. – М.: Машиностроение, 1989. – 400 с.
Пшибыльский, В.В. Технология поверхностной пластической обработки / В.В. Пшибыльский. – М.: Металлургия, 1991. – 479 с.
Кравчук, В.С. Сопротивление деформированию и разрушению поверхностно упрочненных деталей машин и элементов конструкций / В.С. Кравчук, Абу Айаш Юсеф, А.В. Кравчук. – Одесса: Астропринт, 2000. – 160 с.
Чепа, П.А. Эксплуатационные свойства упрочненных деталей / П.А. Чепа, В.А. Андрияшин. – Минск: Наука и техника, 1988. – 191 с.
Смелянский, В.М. Механика упрочнения поверхностного слоя деталей машин в технологических процессах поверхностного пластического деформирования / В.М. Смелянский. – М.: Машиностроение, 1992. – 59 с.
Most read articles by the same author(s)
- D. KAPSKY, D. LEVANOVICH, V. IVANOV, A. GOLOVNICH, IMPROVEMENT OF THE LEGISLATION OF THE REPUBLIC OF BELARUS ON ISSUES OF PHOTO- AND VIDEO RECORDING OF SPEED OFFENSES IN AUTOMATIC MODE, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2021)
- D. KAPSKIY, V. IVANOV, A. GOLOVNICH, V. KUZMENKO, A. KRASILNIKOVA, Ye. GORELIK, S. SEMCHENKOV, Ye. KOT, ASSESSMENT OF THE CONDITION OF THE TRANSPORT SYSTEM OF THE CITIES OF POLOTSK AND NOVOPOLOTSK, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2020)
- V. IVANOV, SCIENTIFIC ARTICLE IN THE DISSERTATION SYSTEM RESEARCH, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2022)
- D. CAPSKI, P. PAGIN, A. GOLOVNITSCH, V. IVANOV, AUDIT OF THE ROAD – A TOOL TO IMPROVE SAFE TRAFFIC NEWS, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2018)
- V. IVANOV, PRESENTATION IN THE OF PROVISIONS MADE ON DEFENSE, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 2 (2023)
- A. DUDAN, T. VIGERINA, V. KRAVCHUK, I. PILIPENOK, INCREASED WEAR RESISTANCE OF PARTS HEAVY-LOADED FRICTION ASSEMBLY OF VEHICLES, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 10 (2022)
- V. IVANOV, STRUCTURAL ELEMENTS OF THE THESIS (content, sequence of presentation, connections and relationships), Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 1 (2023)
- V. IVANOV, MPROVING THE QUALITY OF TRAINING SPECIALISTS IN TECHNICAL OPERATION OF CARS WITH IMPROVEMENT OF THE COURSE "DESIGN OF ENTERPRISES OF VEHICLE TRANSPORT", Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 11 (2020)
- V. IVANOV, A. BONDAREV, А. KULBEI, INVESTIGATION OF FACTORS THAT INFLUENCE THE FORMATION AND DEVELOPMENT OF STRESS CORROSION CRACKING IN GAS PIPELINES, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 3 (2022)
- V. IVANOV, A. DUDAN, T. VIGERINA, S. PILIPENKO, I. PILIPENOK, INCREASING THE ANTIFRICTION PROPERTIES OF PLASTIC LUBRICANT BY MODIFYING WITH MICROSIZED ADDITIVES, Vestnik of Polotsk State University. Part B. Industry. Applied Sciences: No. 2 (2025)